If you’ve noticed a lack of power in your UTV vehicle, you’re probably dreading replacing your UTV fuel pump, but it’s easier than you might think.

The best UTV vehicle is one that works flawlessly. Since most UTVs come equipped with a fuel pump, you must know how to use it properly to ensure a smooth ride.

Continue reading for our step-by-step guide to using a UTV fuel pump so your vehicle will always be ready to hit the trails.

Fuel Pump 101

A fuel pump is a device that pumps fuel from the fuel tank of a UTV to the engine. This is one of the most critical UTV accessories, as it ensures that the engine is supplied with the correct amount of fuel at the right pressure, which is essential for the engine to run smoothly.

UTVs can have either an electric fuel pump or a mechanical fuel pump. Electric fuel pumps are more common in modern UTVs and are powered by electricity from the vehicle's battery. They use an electric motor to draw fuel from the fuel tank and push it to the engine.

Mechanical fuel pumps are powered by the engine's motion and use a diaphragm or piston to draw fuel from the tank and deliver it to the engine. Mechanical fuel pumps are less common in modern UTVs but are still used in some older models. The best UTV vehicle fuel pump is the one that works flawlessly with your vehicle.

In either case, the fuel pump is responsible for delivering fuel to the engine in the right amount and at the proper pressure. If the fuel pump is not working properly, it can cause a variety of issues, such as engine stalling, loss of power, or poor performance. Consequently, it’s essential to maintain the fuel pump properly and ensure it’s working correctly to keep your UTV running efficiently.

Step 1: Check the Fuel Level

Before using the fuel pump, it's important to check the fuel level in the tank. Most UTVs have a fuel gauge that shows the fuel level. If the fuel level is low, it's time to refuel the tank.

Step 2: Locate the Fuel Pump

The fuel pump is located near the fuel tank, often on the underside of the vehicle. It’s a small device that pumps fuel from the tank to the engine. Some UTVs have an electric fuel pump, while others have a mechanical fuel pump.

Step 3: Turn Off the Engine

Before using the fuel pump, it's imperative to turn off the engine. This ensures that the fuel pump isn't pumping fuel while the engine is running, which can cause damage to the fuel system.

Step 4: Connect the Fuel Hose

Once the engine is turned off, it's time to connect the fuel hose to the UTV fuel pump. The fuel hose is usually located near the fuel tank, and it connects directly to the pump. Make sure the hose is securely attached to the pump.

Step 5: Connect the Other End of the Fuel Hose

The other end of the fuel hose should be connected to the fuel container or the gas pump. If you're using a gas pump, make sure the nozzle is securely inserted into the fuel tank. If you're using a fuel container, make sure it’s clean and free of any debris.

Step 6: Prime the Fuel Pump

Before starting the engine, you must prime the fuel pump. This means filling the pump with fuel so it’s ready to pump fuel to the engine. To prime the fuel pump, turn the key to the "on" position for a few seconds, then turn it off. Repeat this process a few times until you see fuel flowing through the hose.

Step 7: Start the Engine

Once the fuel pump is primed, it's time to start the engine. Turn the key to the "start" position and let the engine run for a few seconds. Check to make sure fuel is flowing through the fuel hose to the engine.

Step 8: Monitor the Fuel Level

As you use the UTV, it's necessary to monitor the fuel level. Make sure the fuel tank doesn't run empty, as this can damage the fuel pump. If the fuel level is getting low, it's time to refuel the tank.

Step 9: Disconnect the Fuel Hose

When you're finished using your UTV, disconnect the fuel hose. This ensures that fuel doesn't leak from the tank, which can be a serious fire hazard. Make sure the hose is securely disconnected from the fuel pump and the fuel container or gas pump.

Step 10: Turn Off the Engine

Once the fuel hose is disconnected, turn off the engine. This ensures that the fuel pump isn't pumping fuel while the engine is off, which can cause damage to the fuel system.

How to Keep Your UTV Working Properly

Keeping your UTV running smoothly requires regular maintenance and care. In addition to maintaining the fuel pump, here are some tips to help you keep your UTV accessories and components in top condition:

1. Check and change the oil regularly - Oil is the lifeblood of the engine and needs to be checked and changed regularly. Check the oil level before each ride and change it according to the manufacturer's recommendations.
2. Clean the air filter - The air filter prevents dirt and debris from entering the engine. Clean or replace it regularly, especially if you ride in dusty conditions.
3. Check the brakes - The brakes are critical for your safety, so check them before each ride. Ensure the brake pads are in good condition and that the brake fluid is at the proper level.
4. Check the tires - The tires are the only point of contact between the UTV and the ground, so ensure they are in good condition. Check the tire pressure before each ride and replace the tires if they are worn or damaged.

Visit Terrarider UTV for the Best UTV Vehicle Accessories

Using a UTV fuel pump is a simple process that requires a few concise steps. If you have questions about this process or need to purchase other UTV accessories, visit TerraRider today! By taking proper care of your UTV and its fuel system, you can enjoy many years of reliable use.

We’re a company based in Salt Lake City, Utah, so stop by and meet our friendly staff soon! If you have any questions or need a UTV, contact us today.